Search Results

To promote the development of automated vehicles (AVs), large scale of field operational tests (FOTs) were carried out around the world. Applications of naturalistic driving data should base on correlative scenarios. However, most of the existing scenario typologies, aiming at advanced driving assistance system (ADAS) and extracting discontinuous fragments from driving process, are not suitable for AVs, which need to complete continuous driving tasks. In this paper, a systematic scenario-typology consisting of four layers (from top to bottom: trip, cluster, segment and process) was first proposed. A trip refers to the whole duration from starting at initial parking space to parking at final one. The basic units ‘Process’, during which the vehicle fulfils only one driving task, are classified into parking process, long-, middle- and short-time-driving-processes. A segment consists of two neighboring long-time-driving processes and a middle or/and short one between them.

An online fault detection and isolation (FDI) method for several common sensor faults and even demagnetization of PMSM is proposed by combining model-based and signal analysis technology. To begin with, the field reconstruction method (FRM) of PMSM is employed to obtain the flux residuals which are used as the criterion of fault detection. Then, the flux residuals are transformed by multi sequence harmonic synchronous rotating transformation and inputted into low pass filters (LPFs) in order to obtain the DC components. Last, offset and gain faults of the two phase current sensors, offset fault of the rotor angle sensor and permanent magnet (PM) demagnetization can be isolated by comparing the DC components and preset thresholds. The detection and isolation strategy of PMSM is validated by motor controller hardware in motor bench tests.

In this work, the influences of various real-timely available energy management strategies on vehicle fuel consumption (VFC) and energy flow of a range-extender electric vehicle were studied The strategies include single-point, multi-point, speed-following, and equivalent consumption minimization strategy. In addition, the dynamic programming method which cannot be used in real time, but can provide the optimal solution for a known drive situation was used for comparison. VFCs and energy flow characteristics with different strategies under Worldwide Harmonized Light Vehicles Test Cycle (WLTC) were obtained through computer modeling, and the results were verified experimentally on a range-extender test bench. The experimental results are consistent with the modeled ones in general with a maximum deviation of 4.11%, which verifies the accuracy of the simulation models.

The nonuniformity property of the temperature field distribution will not only affect on the battery charging and discharging performance but also its lifetime. In this paper the elementary structural design is implemented for Ni-Mh battery package and the corresponding test platform is constructed from the point of view of temperature difference control strategy, the test results show that the present structural design schemes can effectively restrain temperature difference enlargement among the battery stacks. Through the application of adopting the flow field uniformity method to control temperature difference, and flow field optimization inside the battery package, it is found that the flow field velocity change quantity ΔV is gradually reduced as the increase of the afflux hood angle Ak and air vent width Da, and the difference of battery temperature is relatively lower, which denoting that the corresponding relationship can be created based on test data.

In recent years, intelligent driving technology is being extensively studied. This paper proposes a path planning method for perpendicular parking based on vehicle kinematics model using MPC optimization, which aims to solve the perpendicular parking task. Firstly, in the case of any initial position and orientation of the vehicle, judging whether the vehicle can be parked at one step according to the location of the parking place and the width of the lane, and then calculating the starting position for parking, and use the Bezier curve to connect the initial position and the starting position. Secondly, reference parking path is calculated according to the collision constraints of the parking space. Finally, because the parking path based on the vehicle kinematics model is composed of circle arcs and straight lines, the curvature of the path is discontinuous. The reference parking path is optimized using Model Predictive Control (MPC).

The separation and analysis of the torque of the permanent magnet synchronous motor is of great significance for optimizing the torque output of the motor. Based on the frozen permeability method, the virtual work principle (VWP) or the Maxwell stress tensor method (MSTM) is often used to separate the torque for torque analysis. However, considering the influence of non-ideal factors such as motor saturation, cross-coupling and flux harmonics, there are differences in torque separation between the VWP and the MSTM, which has been researched and analyzed in this paper. Based on this, for the assisted airspace barrier design of a surface-inserted permanent magnet synchronous motor, to conduct theoretical research on the torque optimization design, this paper uses the VWP to separate the average torque and the MSTM to separate the torque ripple.

As the international community strengthens the control of carbon dioxide emissions, electric vehicles have gradually become a substitute for internal combustion engine vehicles. The battery pack is one of the most important components of electric vehicles. The strength and fatigue performance of the battery support plate not only affect the performance of the vehicle but also concern the safety of the driver. In the present study, the finite element model of a battery pack for fatigue analysis is completely established. The random vibration stress response analysis and acceleration power spectral density response analysis of the support plate for the battery pack are carried out, and the accuracy of the finite element model is verified by a random vibration test.

The diesel engine is the core in the field of engineering machine power plants. While both at home and abroad for the cold start of diesel engine, the transient emission characteristics below 0 °C and above 2000m is almost a blank. Therefore, aimed at high altitude and low-temperature environment emission characteristics of cold start, this article has carried on the systematic analysis and research. In this paper, a simulation test system for the cold start of the diesel engine at low temperature at high altitude is established. The cold start experiments of a heavy diesel engine at different ambient temperatures (10°C, 0°C, -10°C and -20°C) and different altitudes (0m, 3000m, and 4000m) is carried out. In this paper, the gas emission of the diesel engine during the speed-up period of cold start is studied.

Diesel engine is vital in the industry for its characteristics of low fuel consumption, high-torque, reliability, and durability. Existing diesel engine technology has reached the upper limit. It is difficult to break through the fuel consumption and emission of diesel engines. VVA (Variable Valve Actuation) is a new technology in the field of the diesel engines. In this paper, GT-Suite and ANN (artificial neural network) model are established based on engine experimental data and DoE simulation results. By inputting Intake Valve Opening crake angle (IVO), Intake Valve Angle Multiplier (IVAM) and Exhaust Valve Angle Multiplier (EVAM) into the ANN Model, and by using SA (simulated annealing algorithm), the optimized results of intake and exhaust valve lift under the target conditions are obtained.

With the degradation of lithium-ion batteries, the battery safety performance changes, which further influences the safe working window. In this paper, the pouch ternary lithium-ion battery whose rated capacity is 4.2 Ah is used as the research object to investigate the impact of the high-temperature calendar and cyclic aging on tolerance performance. The overcharge-to-thermal-runaway test is performed on the fresh cell and aged cell (90% SOH). The inflection point of voltage for aged cells appears earlier than that of the fresh cell, while the voltage corresponding to the inflection point is the same for them, which means that the voltage at which lithium plating occurs is the same. However, the voltage plateau and the crest voltage before thermal runaway of aged cell are significantly higher than that of the fresh cell. Besides, ohmic heat, reversible heat, and side reaction heat make contribution to the thermal runaway triggering.

To improve the durability of Proton-exchange membrane fuel cell (PEMFC) in actual transportation application scenario, the research on fault diagnosis of PEMFC is receiving extensive attention. With the development of artificial intelligence, performing fault diagnosis with the massive sampling data of the fuel cell system has become a popular research topic. But few people have successfully verified the diagnosis performance of these artificial intelligence algorithms on a real high power on-board PEMFC system. Therefore, we intend to make a step forward with these data-driven artificial intelligence algorithms. We applied four data-driven artificial intelligence algorithms to diagnose three common faults of PEMFC (each fault type has two severity levels, slight and severe). AVL CRUISE M was firstly applied for generation of simulation fault dataset to speed up the algorithm screening process. Based on the dataset, these algorithms are trained and optimized.

Proton exchange membrane fuel cell (PEMFC) system is considered as one of the most popular power sources because of its high energy density, fast dynamic response and zero pollution. However, the start-up at low temperature (e.g. - 30 °C) is still a major challenge for its wide application due to water freezing in Membrane Electrode Assembly (MEA). In this paper, a cold start test process in an environment cabin with auxiliary heat was carried out for a full power automotive PEMFC system, including normal operation, shutdown purge and cold start processes analysis from -30°C. Rated power of this stack is 100kW at the current density of 1.4A/cm2 and relevant maximum output power can reach to 120kW. In order to reduce the damage of high potential to MEA, on-load purge with a current of 30A is conducted to removing extra water in stack for improving cold start ability. Based on corresponding control strategy, cold start was realized successfully within 110s.

Alternating current (AC) heating is an efficient and homogeneous manner to warm Lithium-ion batteries (LIBs) up. The integrated design of AC heating combined with the motor drive circuit has been studied by many scholars. However, the problems of excessive heating frequency (>1kHz) and zeros torque output of the motor during the heating process have not been solved. High-frequency AC excitation may be detrimental to the battery because the effect of high-frequency AC excitation on the state of health of the battery is unknown. In addition, although the zero-torque output can be realized by controlling the q-axis current to zero, the torque ripple is still difficult to eliminate in a real-world application. To further solve the above problems, the motor’s neutral conductor is pulled out and connected to a large capacitor to increase the current amplitude of the AC heating at low frequencies.

To overcome the shortcoming that vehicles with multiple steering modes need to switch steering modes at parking or very low speeds, a dynamic switch method of steering modes based on MOEA/D (Multi-objective Evolutionary Algorithm Based on Decomposition) was proposed for 4WID-4WIS (Four Wheel Independent Drive-Four Wheel Independent Steering) electric vehicle, considering the smoothness of dynamic switch, the lateral stability of the vehicle and the energy economy of tires. First of all, the vehicle model of 4WID-4WIS was established, and steering modes were introduced and analyzed. Secondly, the conditions for the dynamic switch of steering modes were designed with the goal of stability and safety. According to different constraints, the control strategy was formulated to obtain the target angle of the active wheels. Then aiming at the smoothness of the dynamic switch, the active wheel angle trajectory was constructed based on the B-spline theory.

Powertrain system of series-parallel hybrid vehicle contains multiple excitation sources like engine, motor and generator. The reduction of noise and vibration is quite difficult during multiplex working modes or the switch of modes. Aiming at Series-parallel hybrid powertrain system which contains engine, motor and planetary gear subsystems, this paper considered a typical working condition which is based on the power control strategy and established the torsional vibration mechanical model of hybrid powertrain system. The inherent characteristics and transient vibration response of the electric mode, hybrid mode and parking charging mode were studied and it was discovered that the repetitive frequency of the powertrain system under the three working modes is the same which is only related to inertia and meshing stiffness of planetary gear system. The non-repetitive frequency and corresponding vibration modes under the electric mode and parking charging mode are both close.

Cold start capability is one of remaining major challenges in realizing PEMFC (Proton Exchange Membrane Fuel Cell) technology for automotive applications. Gas purge is a common and integral shutdown procedure of a PEMFC automotive in subzero temperature. A dryer membrane electrode assembly (MEA) can store more water before it gets saturated and ice starts to penetrate in the open pores of porous media, thus enhancing cold start capability of a PEMFC. Therefore, gas purge is always performed prior to fuel cell shutdown to minimize residual water in a PEMFC. In the hope of improving effectiveness of purge in a PEMFC vehicle, two important purge parameters are evaluated including purge time and energy requirement. In practice, an optimized gas purge protocol should be developed with minimal parasitic energy, short purge duration and no degradation of components. To conclude, the cold start capability and performance can be consolidated by proper design of gas purge strategies.

Electromagnetic compatibility of electric vehicles is withstanding great challenges because of multiple ECU and actuators distributed in vehicle. At present, researches on electromagnetic characteristics of vehicle mainly focus on rectification based on the EMC experiment, which take much time and energy. Thus, this paper adopts the way of computer simulation studying the electromagnetism model and electromagnetic characteristics of electric vehicle with following procedure. Firstly, the equivalent model of wiring harness was deduced and built. Harnesses were divided into different groups according to terminal reflection property. The equivalent unit parameter matrix was calculated to build the equivalent wiring harness. The crosstalk and radiation cases were set to check the equivalent harness method.

Due to the differences in traffic situations and traffic safety laws, standards for extraction of critical driving scenarios (CDSs) vary from different countries and areas around the world. To maintain the characteristic variables under the Chinese typical CDSs, this paper uses the three-layer detection method to extract and detect CDSs in the Natural Driving Data from China-FOT project which executing under the real traffic situation in China. The first layer of detection is mainly based on the feature distributions which deviate from normal driving situations. These distributions associated with speed and longitudinal acceleration/lateral acceleration/yaw rate also quantify the critical levels classification.

As the core component of electric vehicles (EVs), batteries attach increasingly general attention along with the rapid expansion of electric vehicle market. Battery performance effect directly the safety and reliability of the EVs, so its managing technologies are more and more crucial. Among them, the methods of estimating the state of health (SoH) and predicting remaining useful life become the focuses, which are essential to ensure their dependability and optimum performance over time. This paper mainly focuses on impedance modeling and aging research (aging diagnosis and life prediction) of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS) technique is used to obtain impedance characteristic of batteries. On the one hand, equivalent circuit modeling (ECM) can be motivated by EIS, with the goal to fit measured impedance data using circuit elements.

A rapid path-planning algorithm that generates drivable paths for an autonomous vehicle operating in structural road is proposed in this paper. Cubic B-spline curve is adopted to generating smooth path for continuous curvature and, more, parametric basic points of the spline is adjusted to controlling the curvature extremum for kinematic constraints on vehicle. Other than previous approaches such as inverse kinematics, model-based prediction postprocess approach or closed-loop forward simulation, using the kinematics model in each iteration of path for smoothing and controlling curvature leading to time consumption increasing, our method characterized the vehicle curvature constraint by the minimum length of segment line, which synchronously realized constraint and smooth for generating path. And Differ from the path of robot escaping from a maze, the intelligent vehicle traveling on road in structured environments needs to meet the traffic rules.